Exploring Basic Plumbing When You Install a Bathtub
Exploring Basic Plumbing When You Install a Bathtub
Blog Article
We have noticed this post on Tools You Need to Install a New Bathtub directly below on the internet and thought it made sense to relate it with you on my blog.
Mounting a bath tub isn't precisely rocket science, yet it does require strong plumbing, carpentry, and also occasionally, tiling skills. Changing an old bathtub with a new one is additionally a reasonably difficult project. If the old tub is conveniently available, the job can move easily; if you have to open a wall surface to eliminate the old tub and also place the brand-new bathtub, the job is a lot harder. In either situation, the job is within a residence handyman's skills, although you will require an assistant to vacate the old bathtub and set in the new one. Make certain you have actually certified on your own for the job and fit attempting it. Instead of employing a professional to take over a halfway-completed job, it is better to take into consideration employing one before you start. Opportunities are you may need an expert plumber to make tube connections.
This article will assist you set up a brand-new tub in your restroom if you have actually already bought a brand-new tub and don't require to change the setup of your previous water system pipes.
Your tools as well as material list need to consist of the following:
Removing Old Touches
If you require to replace old faucets with brand-new ones as a part of your installation, after that the first thing you must do is detach the water. After doing so, activate the faucets to drain any water staying in the system. The procedure of eliminating the existing taps can be rather bothersome as a result of the limited access that is usually the case.
Use a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipes to the faucets. Have a towel ready for the staying water that will certainly originate from the pipes. As soon as the supply pipes have been gotten rid of, utilize the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from transforming during this procedure. As soon as the taps have been gotten rid of, the holes in the bath/basin will have to be cleansed of any old sealing compound.
Prior to moving on to fit the new faucets, contrast the pipe links on the old taps to the brand-new faucets. If the old taps are longer than the new taps, then a shank adapter is required for the new taps to fit.
Fitting New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic port to avoid damage to the thread. One end of the port fits on the plastic tail of the tap and also the other end provides a link to the current supply pipelines.
If you need to fit a monobloc, after that you will certainly require minimizing couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next off, position the tap in the installing hole in the bath/basin guaranteeing that the washing machines remain in location in between the faucet and the sink. Protect the tap in place with the producer given backnut. When the faucet is securely in position, the supply pipelines can be connected to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with regular tap ports. The previous type should be linked to the tap ends initially, tightening only by hand. The supply pipelines can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Installing the Bathtub
Utilizing the two wooden boards under its feet, place the bathtub in the required position. The wood boards are helpful in equally spreading the weight of the bath tub over the location of the boards instead of focusing all the weight onto 4 tiny points.
The following goal is to ensure that the bath tub is leveled all round. This can be attained by checking the spirit level as well as changing the feet on the tub till the spirit level reviews degree.
To set up faucets, fit the bottom of the outermost versatile faucet connector to the ideal supply pipe by making a compression sign up with; then do the exact same for the other faucet.
Switch on the water system as well as examine all joints as well as new pipework for leakages as well as tighten them if required. Load the bathtub and likewise inspect the overflow electrical outlet and the normal outlet for leaks.
Lastly, fix the bath paneling as described in the maker's user's manual. Tiling and also securing around the bath tub should wait up until the bath tub has actually been made use of at least once as this will certainly resolve it right into its last setting.
Planning for the Setup
To start with, the supporting structure provided with the bathroom must be fitted (if called for) according to the manufacturer's instructions. Next, fit the taps or mixer to the bath tub. When suitable the faucet block, it is very important to ensure that if the faucet comes with a plastic washing machine, it is fitted between the bath as well as the faucets. On a plastic bath, it is additionally sensible to fit a supporting plate under the taps system to stop stress on the bathtub.
Fit the flexible tap connectors to the bottom of the two taps using 2 nuts as well as olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet through the hole in the bath. Use the nut provided by the manufacturer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bath. Ensure you use all of the supplied washers.
Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom should currently be ready to be fitted in its final position.
Tiling Around the Tub
In the area where the bath satisfies the tile, it is necessary to seal the joins with a silicone rubber caulking. This is essential as the installation can move sufficient to fracture a stiff seal, creating the water to penetrate the wall surface between the bathroom and the tiling, causing complications with wetness as well as possible leaks to the ceiling below.
You can pick from a selection of coloured sealers to assimilate your components as well as installations. They are offered in tubes as well as cartridges, and are capable of sealing gaps as much as a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with spins of drenched paper or soft rope. Bear in mind to always fill up the bath tub with water prior to sealing, to enable the motion experienced when the bathtub is in usage. The sealer can fracture relatively early if you do not think about this activity before securing.
Additionally, ceramic coving or quadrant floor tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also quickly offered on the marketplace. It is advisable to fit the floor tiles making use of water-resistant or water-proof adhesive and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We had been made aware of that editorial about How to Install a Bathtub Yourself through a good friend on a different site. So long as you enjoyed our article if you please don't forget to share it. Thank you for taking the time to read it.
Avoid property damage; contact us. Report this page